ZX81CCP

ZX80 / ZX81 hardware and software offered for sale or swapping
User avatar
msansom
Posts: 37
Joined: Thu Feb 09, 2017 1:38 am

Re: ZX81CCP

Post by msansom » Sat Apr 15, 2017 6:03 am

Going to install mine this weekend.

Is there any trick to getting the old RF modulator out?
I'd like to say thank you on behalf of the group and ourselves and I hope we've passed the audition.

User avatar
1024MAK
Posts: 1766
Joined: Mon Sep 26, 2011 9:56 am
Location: Looking forward to summer in Somerset, UK...

Re: ZX81CCP

Post by 1024MAK » Sat Apr 15, 2017 7:48 am

Do you mean the whole thing including the metal case, or just the PCB inside?

To remove the metal case, desolder the metal tabs that go through the ZX81 PCB. You need a powerful iron with a large tip, or you stand no chance.

To remove the PCB from inside a modulator, cut off all wires to it, desolder the resistor connection to the phono/RCA socket.
If there is a screening plate separating the components on the PCB, remove this.
Then leaver/lift out the PCB.

Note that it has been a while since I last did this, so I may have forgotten an important detail :roll:

Mark

User avatar
PokeMon
Posts: 2128
Joined: Sat Sep 17, 2011 5:48 pm

Re: ZX81CCP

Post by PokeMon » Sat Apr 15, 2017 11:33 am

blittled wrote:
Sat Apr 15, 2017 1:59 am
What size Phillip Screw driver is used on the pots. Is it a 0#, 00#, 1#,etc? I need to make an adjustment and all my small screwdrivers won't work well.
Don't use a Philips driver - take a normal with a slot only. See here:

http://sinclairzxworld.com/viewtopic.ph ... =30#p21770

Put the driver in the wider of both (crossing) slots.

User avatar
PokeMon
Posts: 2128
Joined: Sat Sep 17, 2011 5:48 pm

Re: ZX81CCP

Post by PokeMon » Sat Apr 15, 2017 11:38 am

msansom wrote:
Sat Apr 15, 2017 6:03 am
Going to install mine this weekend.

Is there any trick to getting the old RF modulator out?
This is a hard job to get all of it out as the metal case takes all the heat from your iron. If you just want to use the inbuilt chinch connector of the RF case than it is sufficient just to remove the wire internally going to the middle pin, feed the yellow or now brown cable into the free plastic hole and solder it on the middle pin instead. It is also possible to solder a small capacitor of 100pF or similar between old (removed) wire and middle pin (in series) to have both, video out and RF out. Not sure if this will be totally free of distortions but you may try as some other people did.

The board can be sticked with adhesive tape anywhere in the near, on top of the cpu for example. I can not find a suitable foto right now but maybe other users have ...
Good luck !

rcade
Posts: 12
Joined: Tue Dec 02, 2014 1:28 pm

Re: ZX81CCP

Post by rcade » Fri Apr 28, 2017 1:28 am

I received my boards this past weekend. I installed one in my USA ZX81 and it looks great!

Lardo Boffin
Posts: 622
Joined: Sat Nov 26, 2016 1:42 am

Re: ZX81CCP

Post by Lardo Boffin » Sat Jun 10, 2017 2:50 pm

Hi Pokemon

Just wondering when some more ZX8-CCBs will be back up for sale? I'm down to my last one!

Thanks

Lardo
ZX81 iss 1 (bugged ROM, kludge fix, normal, kit)
Iss 3 with ZXVid, another in nearly perfect box
TS 1000 iss 3, ZXPand AY, ZX8-CCB & ZX-KDLX
TS 1500
TS 2000
Spectrum 16k (iss 1 s/n 1499)
Spectrum 48k
Toastrack + DIVMMC future

User avatar
PokeMon
Posts: 2128
Joined: Sat Sep 17, 2011 5:48 pm

Re: ZX81CCP

Post by PokeMon » Sat Jun 10, 2017 6:27 pm

In the moment out but already pipelined to be produced new. I will follow up here with more information soon.

User avatar
PokeMon
Posts: 2128
Joined: Sat Sep 17, 2011 5:48 pm

Re: ZX81CCP

Post by PokeMon » Tue Jul 04, 2017 10:50 am

So the first good news is, ZX8-CCB is still available.
The second good news is, that I have less work shipping them out (but soldering cables still needed from me).
The third good news is, that it has industrial soldering quality. 8-)

The bad news is, that the price requires to be increased to EUR 9.90 (was EUR 7.50 before) due to this production cost, financing and taking risk of unsold boards and the requirement of maybe doing a new production run if the last board was sold again. So initial cost was much higher than just ordering the boards only and components as requested in lower quantities. Anyway it is at the end still cheaper than ZXvid and may found interest by retro fans. At least I did spend about 1000 EUR first, but there is a minimum quantity order to get the cost down ... :shock:

Here are pictures (more boards produced than shown here)


20170704_104312k.jpg
20170704_104312k.jpg (579.3 KiB) Viewed 194 times
20170704_104348k.jpg
20170704_104348k.jpg (241.94 KiB) Viewed 194 times

Lardo Boffin
Posts: 622
Joined: Sat Nov 26, 2016 1:42 am

Re: ZX81CCP

Post by Lardo Boffin » Tue Jul 04, 2017 11:09 am

Still superb value for money! Several have been ordered. :D
ZX81 iss 1 (bugged ROM, kludge fix, normal, kit)
Iss 3 with ZXVid, another in nearly perfect box
TS 1000 iss 3, ZXPand AY, ZX8-CCB & ZX-KDLX
TS 1500
TS 2000
Spectrum 16k (iss 1 s/n 1499)
Spectrum 48k
Toastrack + DIVMMC future

User avatar
sirmorris
Posts: 2659
Joined: Thu May 08, 2008 4:45 pm
Location: oxon, uk

Re: ZX81CCP

Post by sirmorris » Tue Jul 04, 2017 11:21 am

PokeMon wrote:
Tue Jul 04, 2017 10:50 am
... taking risk of unsold boards ...
As if ;) :lol:

Thanks for your hard work Karl, I'll be ordering some very soon.
--=== ZXpand+ ... A more moderner all-in-one upgrade solution for ZX81 ===--
* SD/MMC storage * 32K Hires-capable RAM * AY sound chip * Joystick port * Serial *
* BASIC enhancements - plug & play * Reset button * Auto-boot facility *

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest