UK700 PSU running at 18.1 volts

Discussions about Sinclair ZX80 and ZX81 Hardware
Lardo Boffin
Posts: 2160
Joined: Sat Nov 26, 2016 2:42 am

UK700 PSU running at 18.1 volts

Post by Lardo Boffin »

Hi all

I have just bought a zeddy with a PSU that runs at 18.1 or so volts with nothing attached. Needless to say I have not plugged this PSU into the zeddy! Is this a safe operating voltage for one of these? Most of the ones I have tested have run at around 14 to 15V without load.

Lardo
ZX80
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
gozzo
Posts: 452
Joined: Fri Jul 08, 2011 8:52 pm

Re: UK700 PSU running at 18.1 volts

Post by gozzo »

hmm, may have shorted turns on the primary winding, does it get warm/hot after a while when on no load? if so it could have. also test voltage with a reasonable load...
gozzo
Posts: 452
Joined: Fri Jul 08, 2011 8:52 pm

Re: UK700 PSU running at 18.1 volts

Post by gozzo »

and ..what mains voltage is it rated for and what is it running on. if its designed for 220v (but that would normally be a EU700? or something like that?) and being run on 240v , it will be high....maybe has a 220v transformer fitted in a uk/240v case???
User avatar
1024MAK
Posts: 5103
Joined: Mon Sep 26, 2011 10:56 am
Location: Looking forward to summer in Somerset, UK...

Re: UK700 PSU running at 18.1 volts

Post by 1024MAK »

I have tested a number of UK700 and UK1200 Sinclair PSUs. The maximum unloaded output voltage is normally 16V.

The electrolytic capacitor(s) inside the PSU is normally rated at 16V, so this may not be happy with the over voltage.

As to a ZX81, the 7805 voltage regulator has a maximum input voltage of between 30V to 35V (depending on manufacturer). However the manufacturer recommendation is to operate them at no more than 25V.

As the "9V" input does not feed anything else inside a ZX81, it should not harm a ZX81.

However, if the "rogue" PSU outputs a higher than normal voltage when connected to a ZX81, the 7805 heatsink will run significantly hotter than normal, and this PSU may damage some third party 16k byte RAM expansions.

Mark
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Buffer Amp

:!: Standby alert :!:
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb :!:
Looking forward to summer later in the year.
User avatar
1024MAK
Posts: 5103
Joined: Mon Sep 26, 2011 10:56 am
Location: Looking forward to summer in Somerset, UK...

Re: UK700 PSU running at 18.1 volts

Post by 1024MAK »

gozzo wrote: Mon Oct 23, 2017 7:26 pm and ..what mains voltage is it rated for and what is it running on. if its designed for 220v (but that would normally be a EU700? or something like that?) and being run on 240v , it will be high....maybe has a 220v transformer fitted in a uk/240v case???
Sinclair PSUs have been found with the wrong label (or case) fitted before...
Just like everything else "made" by Sinclair, the production of their PSUs was done by a number of different companies. I have found four designs so far just for the UK700 version...

Mark
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Buffer Amp

:!: Standby alert :!:
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb :!:
Looking forward to summer later in the year.
Lardo Boffin
Posts: 2160
Joined: Sat Nov 26, 2016 2:42 am

Re: UK700 PSU running at 18.1 volts

Post by Lardo Boffin »

1024MAK wrote: Mon Oct 23, 2017 8:27 pm
However, if the "rogue" PSU outputs a higher than normal voltage when connected to a ZX81, the 7805 heatsink will run significantly hotter than normal, and this PSU may damage some third party 16k byte RAM expansions.

Mark
That’s an interesting point about the plug ins. This zeddy has hardly been used - it is in superb condition. Even the paint on the PSU is pristine. It came bundled with a memotech 16k RAM pack which is also pristine but does not work. It either produces a black screen or various patterns on other zeddys.
I wonder if the over zealous PSU killed it? Regardless I guess I will need to find another one to go with this zeddy before I sell it.
If this PSU is any use to anyone they are welcome to it for p&p.
ZX80
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
Lardo Boffin
Posts: 2160
Joined: Sat Nov 26, 2016 2:42 am

Re: UK700 PSU running at 18.1 volts

Post by Lardo Boffin »

On the plus side a dead memotech RAM pack means my ZXpand finally has a home! Although it is an original plus AY so that complicates it somewhat. :roll:
ZX80
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
Lardo Boffin
Posts: 2160
Joined: Sat Nov 26, 2016 2:42 am

Re: UK700 PSU running at 18.1 volts

Post by Lardo Boffin »

I took the lid off and took some photos. It does have a 16V capacitor so presumably it is the correct internals just incorrectly built?
7EBB1B2B-9A96-4175-BACA-ADC15CFBC595.jpeg
(600.26 KiB) Downloaded 327 times
4BBE0174-3D72-45AC-A491-729234C25B84.jpeg
(506.92 KiB) Downloaded 327 times
B02992E5-F3E0-472D-93C9-378EB898BA11.jpeg
(548.3 KiB) Downloaded 327 times
ZX80
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
User avatar
1024MAK
Posts: 5103
Joined: Mon Sep 26, 2011 10:56 am
Location: Looking forward to summer in Somerset, UK...

Re: UK700 PSU running at 18.1 volts

Post by 1024MAK »

Most likely, the transformer has been wound for a 220V mains supply.

Unloaded, a small mains transformer can produce an output voltage that is greater than the rating by between 15% and 25%.

If your local mains voltage is slightly high (although officially our mains is now 230V AC, in practice the power distribution companies have not changed most of the existing transformers, and these often give a voltage of between 235V and 250V).

Combined, these two factors alone can result in an output that is 20 to 40% higher.

Then take account of the 2200uF capacitor, which with no load, is charging up to the peak rectified secondary voltage (AC voltage x 1.414 gives the peak DC voltage), and you can see why the unloaded DC voltage can be much greater than the nominal 9V DC voltage. Often between 12V and 16V, and in this case, 18.1V...

Mark
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Buffer Amp

:!: Standby alert :!:
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb :!:
Looking forward to summer later in the year.
User avatar
gammaray
Posts: 590
Joined: Sun Apr 17, 2016 2:44 am
Location: Texas

Re: UK700 PSU running at 18.1 volts

Post by gammaray »

If anybody cares... it is rogue as in outlier not rouge as in makeup :?
5-TS1000,UK ZX81<-Sheelagh, US ZX81, 2-TS1500/KDLX , 3-TS2040 printer, 2-TS2020 cassette decks, ZXPAND+AY, ZeddyNET, ZXBlast, UDG, ZX8CCB, AERCO, BUILDS/REPAIRS ZX Spectrum, ZX80 Minstrel, ZXMAX48 v1 v2, 2-TS-2068, ROM, 16kRAM
Post Reply