How to repair a ZX81XT extender board (or slot edge connector)

Discussions about Sinclair ZX80 and ZX81 Hardware
Post Reply
User avatar
PokeMon
Posts: 2264
Joined: Sat Sep 17, 2011 6:48 pm

How to repair a ZX81XT extender board (or slot edge connector)

Post by PokeMon »

* HOWTO instruction *

Well - one day with bad luck, to much force, bad angle or whatever it may happen, that one of the contacts of slot edge connector is bended and moved inside the connector and while trying to fit it deeper onto the edge connector you press it more inside like this:
20170501_155245k.jpg
20170501_155245k.jpg (83.57 KiB) Viewed 2734 times
The repair is quite simple with few tools and a soldering iron. Contacts can be removed and replaced easily. First heat the soldering of the contact and bend it back into the straight position.
20170501_155301k.jpg
20170501_155301k.jpg (115.05 KiB) Viewed 2734 times
Then you can move the contact outside in slightly pushing it to the connector open side. Avoid bending - best to do this is to use a side cutter, grab it and push it in the desired direction. Be careful not to cut it accidently ...
20170501_155413k.jpg
20170501_155413k.jpg (162.33 KiB) Viewed 2734 times
User avatar
PokeMon
Posts: 2264
Joined: Sat Sep 17, 2011 6:48 pm

Re: How to repair a ZX81XT extender board (or slot edge connector)

Post by PokeMon »

Here it comes and now you can easily grab it from the front side with a tweezer or a side cutter or a small screwdriver to pull it out completely.
20170501_155433k.jpg
20170501_155433k.jpg (89.16 KiB) Viewed 2726 times
Then you need a new contact feather or spring (don't know the correct name of this) - I have a small box and collected many over the time, so easy for me to find. You may also take another unused connector to take from. Be sure it is of same type, there are different types used ... (the upper one is the bad contact and below shown a new contact)
20170501_155624k.jpg
20170501_155624k.jpg (68.15 KiB) Viewed 2726 times
Then you can simply put it back into the edge connector from frontside while carefully moving it deeper into it's hole and see coming out from the other side.
20170501_155659k.jpg
20170501_155659k.jpg (88.07 KiB) Viewed 2726 times
Last edited by PokeMon on Mon May 01, 2017 4:40 pm, edited 1 time in total.
User avatar
PokeMon
Posts: 2264
Joined: Sat Sep 17, 2011 6:48 pm

Re: How to repair a ZX81XT extender board (or slot edge connector)

Post by PokeMon »

You may take it now from the other side and pull it deeper into the connector until the right position is found (as deep as the others). Better to pull then to push it too much from the other side as it has to be handled carefully.
20170501_155706k.jpg
20170501_155706k.jpg (114.59 KiB) Viewed 2726 times
Then bend it back to reach the pcb and heat the soldering and move it near the board and let it solder back again.
20170501_155806k.jpg
20170501_155806k.jpg (115.57 KiB) Viewed 2726 times
That's it - now it looks fantastic again like new and (most important) will work again. 8-)
20170501_155800k.jpg
20170501_155800k.jpg (68.37 KiB) Viewed 2726 times
Last edited by PokeMon on Tue May 02, 2017 12:33 am, edited 1 time in total.
User avatar
1024MAK
Posts: 5102
Joined: Mon Sep 26, 2011 10:56 am
Location: Looking forward to summer in Somerset, UK...

Re: How to repair a ZX81XT extender board (or slot edge connector)

Post by 1024MAK »

Edge connector surgery with Doctor PokeMon :ugeek:

With new edge-connectors that need cutting down to size, I keep the spare bit for this very reason ;)

Mark
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Buffer Amp

:!: Standby alert :!:
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb :!:
Looking forward to summer later in the year.
sirmorris
Posts: 2811
Joined: Thu May 08, 2008 5:45 pm

Re: How to repair a ZX81XT extender board (or slot edge connector)

Post by sirmorris »

Ha! Yes, _exactly_ what I do when that happens (all too often) to me. My own boards get a lot of abuse and a damaged edgey is a common complaint.

Sometimes I find that the spring wants to escape into the central space, especially if the plastic around the spring's position is slightly damaged. When this happens I insert a piece of PCB material into the connector before inserting the spring, so that the new spring is pushed/pulled into its seat properly.

Great guide Karl!
User avatar
mrtinb
Posts: 1906
Joined: Fri Nov 06, 2015 5:44 pm
Location: Denmark
Contact:

Re: How to repair a ZX81XT extender board (or slot edge connector)

Post by mrtinb »

I have used a ZX81XT to get space between my Lambda 8300 and the ZXBKBv3 keyboard controller I've built. But yesterday all kinds of chars came randomly on the screen, but the computer worked. It was hard to use, as most of the chars on the screen were corrupted.

This was very frustrating. Finally I saw that one of these connectors was broken. I replaced the ZX81XT with a UDG-for-ZXpand card, and everything worked.

Thanks for the great dokumentation to fix this. I need the ZX81XT to use my ZXblast.
Martin
https://zx.rtin.be
ZX81, Lambda 8300, Commodore 64, Mac G4 Cube
Post Reply