Yet another ROM adapter
Re: Yet another ROM adapter
moordean, good advise about soldering SMD components. PersonallyI found that soldering any 1206, 805 or even 603 packages is not difficult with a tip 0.8mm dia. At first I clean the PCB with IPA, then apply a bit of good quality flux on the pads and finally solder with a small portion of solder on the tip. An ESD teasers are very helpful. When all SMD components are in their places I do final cleaning any residue of flux from the board.
I would not agree that the soldering the adapter to the ZX81 board directly is the solution. In my opinion any modification should reversible as far as practically possible. I don't like any mods that require traces cutting, drilling additional holes, and so on. I've repaired a few boards (mainly ZX Spectrums) where someone solder "add-on" directly to the board. In most of the cases there was a bad joint, broken traces or very badly overheated board with lifted/broken traces.
Coming back to your adapter, could you use all components in SMD packages including both capacitors in next revision of the board? MLCC 4.7uF/10V is available in 805 size. In KiCAD you can also find components' footprint for hand soldering. Pads are longer and they are really handy. Yes, they require more space on the PCB but it is not the case on your board.
I would not agree that the soldering the adapter to the ZX81 board directly is the solution. In my opinion any modification should reversible as far as practically possible. I don't like any mods that require traces cutting, drilling additional holes, and so on. I've repaired a few boards (mainly ZX Spectrums) where someone solder "add-on" directly to the board. In most of the cases there was a bad joint, broken traces or very badly overheated board with lifted/broken traces.
Coming back to your adapter, could you use all components in SMD packages including both capacitors in next revision of the board? MLCC 4.7uF/10V is available in 805 size. In KiCAD you can also find components' footprint for hand soldering. Pads are longer and they are really handy. Yes, they require more space on the PCB but it is not the case on your board.
Claudius
----------
----------
Re: Yet another ROM adapter
Once you insert anything not equal to the shape of the standard ROM pin into a SinclairZX socket a normal ICs pin will not make reliable contact again. So plugging in the Adapter is irreversibleMcKlaud wrote: ↑Fri Dec 22, 2017 8:35 am I would not agree that the soldering the adapter to the ZX81 board directly is the solution. In my opinion any modification should reversible as far as practically possible. I don't like any mods that require traces cutting, drilling additional holes, and so on. I've repaired a few boards (mainly ZX Spectrums) where someone solder "add-on" directly to the board. In most of the cases there was a bad joint, broken traces or very badly overheated board with lifted/broken traces.
In theory, there is no difference between theory and practice. But, in practice, there is.
Re: Yet another ROM adapter
Come on, round pin header are perfectly fine with most of the IC sockets.
I know that IC sockets that Sinclair used in 80-ties are cr... (not decent), but you can replace them very easy with a modern and good quality ones in less than 10 min.
I know that IC sockets that Sinclair used in 80-ties are cr... (not decent), but you can replace them very easy with a modern and good quality ones in less than 10 min.
Claudius
----------
----------
Re: Yet another ROM adapter
If you are happy with desoldering the socket you can desolder the Adapter as well
In theory, there is no difference between theory and practice. But, in practice, there is.
- 1024MAK
- Posts: 5153
- Joined: Mon Sep 26, 2011 10:56 am
- Location: Looking forward to summer in Somerset, UK...
Re: Yet another ROM adapter
The least destructive thing to push into an existing socket (apart from a real IC) is a stamped pin socket:
If height is a problem, then some creative thinking is required
Mark
So if there is sufficient height available, use an inexpensive stamped pin socket in-between the adapter and the original PCB socket.If height is a problem, then some creative thinking is required
Mark
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Buffer Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer later in the year.
ZX81 Chip Pin-outs
ZX81 Video Transistor Buffer Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer later in the year.
Re: Yet another ROM adapter
Yes Mark
You are absolutely right.
It's a solution to the problem which I wasn't aware of (the problem, not the solution )
Only way to have a reversible adaption.
You are absolutely right.
It's a solution to the problem which I wasn't aware of (the problem, not the solution )
Only way to have a reversible adaption.
In theory, there is no difference between theory and practice. But, in practice, there is.
Re: Yet another ROM adapter
Flip pins are an alternative but not very cheap.
http://oshchip.org/products/Flip-Pins_Product
Regards Andy
http://oshchip.org/products/Flip-Pins_Product
Regards Andy
what's that Smell.... smells like fresh flux and solder fumes...
Re: Yet another ROM adapter
Andy, thanks for this info. They are an interesting option, but pricey, very pricey, over $35 for set of 12 units with the delivery to the UK.
Claudius
----------
----------
Re: Yet another ROM adapter
You can buy single pieces on spark fun for 1.50 per 14 pin, so 3.00 for a dip28 socket. Not know how much shipment will be charged but it could be send in an envelope.
https://www.sparkfun.com/products/14086
https://www.sparkfun.com/products/14086
Re: Yet another ROM adapter
What about buying a cheap IC, cracked up und pins reused?
To be honest I prefer to desolder the socket and solder the adapter directly to the PCB.
To be honest I prefer to desolder the socket and solder the adapter directly to the PCB.
In theory, there is no difference between theory and practice. But, in practice, there is.