zx spectrum in zx81 case

McKlaud
Posts: 107
Joined: Tue Dec 19, 2017 10:02 pm
Location: St Albans, UK

Re: zx spectrum in zx81 case

Post by McKlaud » Tue Jan 09, 2018 12:56 am

rune wrote:
Sat Jan 06, 2018 4:27 pm
Nope still the same log. The CPLD is warm. I've checked continuity from the 10 pin header to CPLD and all is good. Voltage to the board is good.
To be honest I bought five (5) CPLD chips from a Far East supplier and only 2 are fine. Anyway, good luck with your board.

@superfo designed an interface to the Issue 1. The interface is a combination of the Kempston type joystick port and the IF2 cartridge slot. It works with any ZX Spectrum and is compact and very handy. See below.

Image

Image

And the last but not least, below is a teaser about the Issue 2 board. This PCB is still hot and arrived to me a few days ago.

Image
Claudius
----------

User avatar
gammaray
Posts: 433
Joined: Sun Apr 17, 2016 2:44 am
Location: Texas

Re: zx spectrum in zx81 case

Post by gammaray » Tue Jan 09, 2018 6:32 pm

nollkolltroll wrote:
Tue Nov 21, 2017 7:30 am
Interesting choice of travel...
Since there is a CPLD or FPGA sitting there, it would presumably be possible to create a ZX80/81/Spectrum switchable in the same case?
Interesting and worthy concept, I wish I knew how!

There would have to be a change in bus layout. Maybe a driver/buffer board to switch signals?

There would have to be a keyboard overlay. Larger ROM for both monitors (Op Sys)

And other things without being an emulator... May be too complicated to implement electrical layout.
Finish what you start. Truth is over the mountaintop or six feet under.
4 x TS1000, 2 x TS1500 , 2 x timex 2040 printer, 1/2 x timex 2020 cassette deck, ZXPAND+AY, ZeddyNET, ZXBlast..., unfinished Spectrum...Still no life!

McKlaud
Posts: 107
Joined: Tue Dec 19, 2017 10:02 pm
Location: St Albans, UK

Re: zx spectrum in zx81 case

Post by McKlaud » Wed Jan 17, 2018 5:16 pm

Newer version of the ZX Max is alive.

Image

I have got two spare PCBs (one white and one blue). If anyone is interested in them, please feel free and send me a PM. Only one rule applies: "First come, first served."
Claudius
----------

McKlaud
Posts: 107
Joined: Tue Dec 19, 2017 10:02 pm
Location: St Albans, UK

Re: zx spectrum in zx81 case

Post by McKlaud » Wed Jan 17, 2018 11:39 pm

All gone :) Lucky guys are: Paul & 1024MAK :)
Claudius
----------

User avatar
msch
Posts: 51
Joined: Sun May 19, 2013 11:39 pm

Re: zx spectrum in zx81 case

Post by msch » Thu Jan 18, 2018 3:19 pm

Beautifull! I really like the yellow/amber PCB...
ZX-Team member, Germany

rune
Posts: 150
Joined: Thu Sep 04, 2014 8:35 am

Re: zx spectrum in zx81 case

Post by rune » Sat Jan 20, 2018 7:33 pm

A bit more info on my build.

Dont buy the IC "packs" from ebay. I got some new CPLDs from elsewhere the first out the packet programmed immediately. Then the Eprom wasnt recognised in either of my programmers. Another eprom programmed fine.

Next the test - lots of coloured squares and the Z80 getting warm. I've tried swapping the RAM, using one at a time and even a new one. It didnt help.

Tomorrow I'll get the CPU swapped out and try some diagnostics on the scope, but those "project" kits seem to be utter rubbish.

McKlaud
Posts: 107
Joined: Tue Dec 19, 2017 10:02 pm
Location: St Albans, UK

Re: zx spectrum in zx81 case

Post by McKlaud » Wed Jan 31, 2018 6:33 pm

The keyboard overlay with the ZX Spectrum layout was designed and made by Dave of Tynemouth Software.
Attachments
ZXlayout.png
ZXlayout.png (1.38 MiB) Viewed 442 times
Claudius
----------

rune
Posts: 150
Joined: Thu Sep 04, 2014 8:35 am

Re: zx spectrum in zx81 case

Post by rune » Wed Jan 31, 2018 6:44 pm

Very, very nice

tynemouthsoftware
Posts: 1
Joined: Wed May 31, 2017 9:40 am

Re: zx spectrum in zx81 case

Post by tynemouthsoftware » Sat Feb 03, 2018 3:05 pm

Thanks to McKlaud for sending me a PCB and a CPLD, I've built up a ZX Max 48 and looked at some keyboard options. The keyboard overlay was an interesting challenge, and I think it has come out very nicely.
Image
As well as using the overlays on a ZX81 case, it also goes very nicely on a perspex baseplate.
ImageAnd since it is the same size as my Minstrel ZX80 clone, the keyboard for that is a good match (other than the . from the ZX80/81 rather than symbol shift).
Image
More photos and info in a new blog post:
http://blog.tynemouthsoftware.co.uk/201 ... ax-48.html
Thanks,
Dave

gozzo
Posts: 448
Joined: Fri Jul 08, 2011 8:52 pm

Re: zx spectrum in zx81 case

Post by gozzo » Sat Feb 03, 2018 3:40 pm

can anyone supply preprogrammed cplds for this zxmax, as i have bought an empty board, can find the other parts easily,.. i do have 3 'used' cplds but as to whether they can be erased and reused i dont know, plus i dont know what software or programmer device would be needed to program them...

Post Reply