My Issue 2 continuing problems and Issue 6s fixed

[redgatemodels]

Ok, quick question for the brains out there. In the service manual it states

A significant cause of problems has been found to be failure of the internal power supply
transistor TR4. The circuit may be improved by changing the value of R60 from 100R to 270R and
connecting a 4.7uF electrolytic (preferably radial type) with positive end to TR5 emitter (positive
end of C34) and negative end to TR5 base (to R58).

Now, I have a 4.7uF cap in the recap kit, but looking at my stocks of resistors from other projects I don’t have a 270R. I do have a 240R or 330R. Would either of these be ok, or do I really have to resort to ordering a few off evilbay???

In better news looks like the machine code mod and the video quality mod mentioned were done at the factory, which is good

[redgatemodels]

Since there was no words of wisdom I’ve ordered 10 270Rs, £1.50 including postage

Second Speccy from eBay arrived today, it’s a 6S. Not had chance to test it yet, but hopefully will work and will prove the tv works etc.

I may put the series 2 pcb in the rubber key case, effectively restoring it to how it was when I first got it and put the 6S in the plus case. Undecided

[1024MAK]

For C74 (the extra 4.7µF capacitor) see this post

I hate to say it, but the value of R60 changed many times (both within each board issue and between different boards) and the final value is 220Ω…

What value is currently fitted?

If you really want to bring the DC/DC converter circuitry up to the last official Sinclair version, see my blog page here

However, it’s a bit more challenging doing this on an issue two board. Have a look at photos of other boards to see the ‘flying’ diodes and other components. It’s also a good idea to get rid of the heatsink for the 7805 by fitting a Recom, Traco Power or MuRata switching regulator / DC/DC converter.

Mark

[redgatemodels]

What value is currently fitted?

Cheers Mark, it’s 100 ohm at the moment

[1024MAK]

Well, if you don’t have a 220Ω, a 240Ω or 270Ω should be okay.

Mark

[redgatemodels]

Nice, I have 240R’s in stock with 270’s on the way from eBay

[redgatemodels]

Today's results.

First the new 6s equipped rubber key cased Speccy. Boots fine, keyboard membrane is shot as expected. Memory etc tests out fine with the diagnostic rom. This has also proved that either the TV rf input is dodgy or the aftermarket lead I bought is rubbish. Lots of noise on the screen, less so on my big lounge TV.

Next the old s2. On first power up it was worse, white border, black screen. However with a little twiddling with the colour trimmers I got a white border. The diagnostic rom would not boot. Don't know what made me do it but I pressed the ula and hey presto got results. I whipped it out and switch cleaned the socket and pins. After refitting we get the copyright message with a white on white display. Looks like the recapping has sorted the colour tuning too.

Next is to get a new membrane for the rubber case and then some comp mods. Oh and the 4.7uF cap and r60 swap for the s2

[1024MAK]

Remember, it only takes a single poor connection of one of the critical pins to completely screw up a digital computer…

Good to hear of plenty of forward progress

Mark

[redgatemodels]

Remember, it only takes a single poor connection of one of the critical pins to completely screw up a digital computer…

Good to hear of plenty of forward progress

Mark

Thanks Mark, it’s great to see proper colours on the s2 at last

Membrane is on order, s6 is installed in the plus case, will probably be my “working” one with the s2 in the rubber case kept as “archive”

[redgatemodels]

Final test today, plugged the s2 into the big telly and have a super stable white display, better than the 6S which has what is best described as interference on the display. Maybe a recap would cure this too? It might be ok with a comp video mod, we will see.