ZX81 ULA-in-a-CPLD
Re: ZX81 ULA-in-a-CPLD
Well some further development while i am waiting for parts to hopefully fix the video noise issue, i thought i would turn to tape input. i couldn't get a simple resistor network to work well, even though in my project setting i have pins set to "float" instead of "keeper" it was still sticking at 2.4 volts... very odd behaviour indeed. so a simple single stage bjt amp was built with a gain of around 15 so the output is very square which was exactly the intention , i think the gain is a little high as for the first time ever i have had to use a substantially lower volume on my cassette player than normal
anyway hopefully with the space freed up by chaging the video circuit i should have enough room for on board transistor amp.
regards.
anyway hopefully with the space freed up by chaging the video circuit i should have enough room for on board transistor amp.
regards.
what's that Smell.... smells like fresh flux and solder fumes...
Re: ZX81 ULA-in-a-CPLD
Hi Andy,
I've faced the same issue when I built the resistor network with the 1.2V bias. It worked well when isolated on a breadboard, but when I plugged the ULA in to the Zeddy's PCB I started reading 2.4-2.5V. Odd. So I gave up with it and just tried to load anything directly with the circuit as it was. I tested with the TZXduino. Everything was fine, software was loaded without errors.
I've faced the same issue when I built the resistor network with the 1.2V bias. It worked well when isolated on a breadboard, but when I plugged the ULA in to the Zeddy's PCB I started reading 2.4-2.5V. Odd. So I gave up with it and just tried to load anything directly with the circuit as it was. I tested with the TZXduino. Everything was fine, software was loaded without errors.
Claudius
----------
----------
Re: ZX81 ULA-in-a-CPLD
Thanks for the confirmation that I wasn't going mad, my circuit is very similar indeed, I need to tweak the gain a little but it's all good stuff ready for the next prototype.
Regards Andy
Regards Andy
what's that Smell.... smells like fresh flux and solder fumes...
Re: ZX81 ULA-in-a-CPLD
nothing beats the feeling you get when a bodge comes together !
Introducing ... DeadBug sot-23-6
big improvement on the video noise, but still have close to 50mv p-p noise ( spike every 1/2 cpu cycle ) , i want to retain the emmiter follower since as i have a 100ohm load on board, this give compatibility with low-z and high-z input monitor / tv making small improvements.
Thanks go to PokeMon and Claudius for hints and ideas.
i haven't had this much fun since.... the last ULA
regards Andy
Introducing ... DeadBug sot-23-6
big improvement on the video noise, but still have close to 50mv p-p noise ( spike every 1/2 cpu cycle ) , i want to retain the emmiter follower since as i have a 100ohm load on board, this give compatibility with low-z and high-z input monitor / tv making small improvements.
Thanks go to PokeMon and Claudius for hints and ideas.
i haven't had this much fun since.... the last ULA
regards Andy
what's that Smell.... smells like fresh flux and solder fumes...
Re: ZX81 ULA-in-a-CPLD
Is slow mode working yet?
Re: ZX81 ULA-in-a-CPLD
In my ULA, still work in progress. Unfortunately I had to pack my toys and locked them up for a few weeks.
@Andy: Are spikes in your case similar to these in red circlers in the attached picture?
Claudius
----------
----------
- 1024MAK
- Posts: 5165
- Joined: Mon Sep 26, 2011 10:56 am
- Location: Looking forward to summer in Somerset, UK...
Re: ZX81 ULA-in-a-CPLD
In the best Sinclair tradition
Keep the bodging ticking over guys
Mark
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer being good this year.
ZX81 Chip Pin-outs
ZX81 Video Transistor Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer being good this year.
Re: ZX81 ULA-in-a-CPLD
similar as in they are spikes... but way more frequent, i can tell you exactly when, every 1/2 clock cycle
what's that Smell.... smells like fresh flux and solder fumes...
Re: ZX81 ULA-in-a-CPLD
all the following are video signal, probe and ground at the ula pins, noise is worse at modulator socket.
this is white video x10 probe so noise is around 80mv p-p
this is a vertical row of inverse spaces rest of the screen is white, the burst of noise at the left coincides with the force nop
lookd ok as a bigger picture levels are close to perfect but still get that horrible verticle banding,
forwards.... its the only way to go
this is white video x10 probe so noise is around 80mv p-p
this is a vertical row of inverse spaces rest of the screen is white, the burst of noise at the left coincides with the force nop
lookd ok as a bigger picture levels are close to perfect but still get that horrible verticle banding,
forwards.... its the only way to go
what's that Smell.... smells like fresh flux and solder fumes...