Spectrum+ 128K Toastrack composite out
-
- Posts: 2191
- Joined: Sat Nov 26, 2016 2:42 am
Spectrum+ 128K Toastrack composite out
Hi all
How do you get a composite image out of a toastrack? I believe one pin in the RGB socket carries the signal? Assuming so does anyone know where I can get a suitable cable (ideally one which carries sound)?
Making them is not my speciality...
Thanks!
How do you get a composite image out of a toastrack? I believe one pin in the RGB socket carries the signal? Assuming so does anyone know where I can get a suitable cable (ideally one which carries sound)?
Making them is not my speciality...
Thanks!
ZX80
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
- 1024MAK
- Posts: 5165
- Joined: Mon Sep 26, 2011 10:56 am
- Location: Looking forward to summer in Somerset, UK...
Re: Spectrum+ 128K Toastrack composite out
Are you up for soldering an insulated wire from a resistor lead to the centre pin of the phono connector in the modulator (after disconnecting the resistor and the input and +5V supply wires)?
Or do you wish to maintain the RF UHF output?
Mark
Or do you wish to maintain the RF UHF output?
Mark
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer being good this year.
ZX81 Chip Pin-outs
ZX81 Video Transistor Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer being good this year.
-
- Posts: 2191
- Joined: Sat Nov 26, 2016 2:42 am
Re: Spectrum+ 128K Toastrack composite out
No problems with losing RF to get composite thanks.
ZX80
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
- 1024MAK
- Posts: 5165
- Joined: Mon Sep 26, 2011 10:56 am
- Location: Looking forward to summer in Somerset, UK...
Re: Spectrum+ 128K Toastrack composite out
Tomorrow then
As I’m about to watch Magnum P.I.
Mark
As I’m about to watch Magnum P.I.
Mark
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer being good this year.
ZX81 Chip Pin-outs
ZX81 Video Transistor Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer being good this year.
-
- Posts: 2191
- Joined: Sat Nov 26, 2016 2:42 am
Re: Spectrum+ 128K Toastrack composite out
Nice!
The reboot?
I have done the RGB mod shown here: https://spectrumforeveryone.com/technic ... compliant/ (replacing R134 etc.) so I may need to do a little roll back first?
ZX80
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
- 1024MAK
- Posts: 5165
- Joined: Mon Sep 26, 2011 10:56 am
- Location: Looking forward to summer in Somerset, UK...
Re: Spectrum+ 128K Toastrack composite out
ZX Spectrum 128k Toastrack Composite Video Modification to the Modulator
Composite video is available on the monitor/RGB socket:
Pin 1 = composite video
Pin 2 = 0V/GND/ground/screen
To replace the RF UHF TV signal from the modulator with a composite video signal, follow these steps:
But Lardo being ‘special’, you have presumably removed R134?
So instead of soldering to one lead of it, you will need to do these steps:
Mark
Composite video is available on the monitor/RGB socket:
Pin 1 = composite video
Pin 2 = 0V/GND/ground/screen
To replace the RF UHF TV signal from the modulator with a composite video signal, follow these steps:
- Disconnect the existing +5V feed wire and the video signal wire for the modulator from the PCB. Either by heating up each of the solder joints until the solder becomes molten, then very gently pulling each of the wires out of the PCB with small long nose pliers. Or you can just cut both wires close to the board. You can then bend them up from the PCB, out of the way.
- Inside the modulator, disconnect the existing resistor that connects to the centre pin of the phono/RCA/Cinch connector on the modulator case.
- Locate resistor R134 (75Ω) on the main board. Use a multimeter on the continuity range (or 200Ω resistance range) to find the lead that connects to pin 1 of the DIN socket.
- Now strip about 3 to 4mm of the insulation from an insulated wire, tin the wire, then solder this to the lead of resistor R134 (75Ω) that you identified in the above step.
- Route the wire through the spare hole in the modulator. Use the shortest route to keep the length as short as possible.
- Then solder the wire to the centre pin of the phono/RCA/Cinch connector on the modulator case.
But Lardo being ‘special’, you have presumably removed R134?
So instead of soldering to one lead of it, you will need to do these steps:
- Disconnect the existing +5V feed wire and the video signal wire for the modulator from the PCB. Either by heating up each of the solder joints until the solder becomes molten, then very gently pulling each of the wires out of the PCB with small long nose pliers. Or you can just cut both wires close to the board. You can then bend them up from the PCB, out of the way.
- Write 500 lines saying “I’ll tell Mark everything I’ve done to my machine when I ask for help”.
- Inside the modulator, disconnect the existing resistor that connects to the centre pin of the phono/RCA/Cinch connector on the modulator case.
- Report yourself to the RSPCA (Respect Sinclair Personal Computers and Accessories) society.
- Locate where resistor R134 was on the main board. Use a multimeter on the continuity range (or 200Ω resistance range) to find the PCB pad/hole for the lead that connects to the emitter pin of transistor TR14 (ZTX313). Keep note of this PCB pad, we will come back to it later.
- Go through your trash can to find that poor 75Ω resistor, or buy a new one (a 250mW / ¼W type or a 500mW / ½W type will be fine).
- Thrash yourself with a branch from a holy tree for taking advice from another site about tinkering with your Sinclair machines.
- Get some black heat-shrink insulated sleeving of a suitable size that it will slide over the 75Ω resistor, plus some smaller diameter heat-shrink to go over the solder joints you will be making to its leads.
- Now strip and solder an insulated wire to one lead of your 75Ω resistor. Do the same for the other lead. Fit the heat-shrink sleeving to the joints and over the resistor.
- Route one of the wires from the 75Ω resistor through the spare hole in the modulator. Use the shortest route to keep the length as short as possible.
- Connect this wire to the centre pin of the phono/RCA/Cinch connector on the modulator case.
- Then solder the other wire from the 75Ω resistor to the former R134 PCB pad that you located earlier (that’s the one that connects to the emitter of TR14).
- Hand in your 500 lines.
- Check. Then double check that there are no possible sources of short circuits, power on and test
Mark
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer being good this year.
ZX81 Chip Pin-outs
ZX81 Video Transistor Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer being good this year.
- 1024MAK
- Posts: 5165
- Joined: Mon Sep 26, 2011 10:56 am
- Location: Looking forward to summer in Somerset, UK...
Re: Spectrum+ 128K Toastrack composite out
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer being good this year.
ZX81 Chip Pin-outs
ZX81 Video Transistor Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer being good this year.
-
- Posts: 2191
- Joined: Sat Nov 26, 2016 2:42 am
Re: Spectrum+ 128K Toastrack composite out
75Ω Resistors ordered.
Lines nearly done.
ZX80
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
-
- Posts: 2191
- Joined: Sat Nov 26, 2016 2:42 am
Re: Spectrum+ 128K Toastrack composite out
Resistors arrived. Lines complete. Reported self to RSPCA.
Working on the assumption that the emitter is on the left and subtly marked E it goes to the pad shown:
Which makes sense as the input to R134 now comes from the 12V carrying cap and goes down to blanking voltage level via the new R134, the other side of which goes directly into pin 1.
So from here on in I am just basically connecting the emitter output via a 75ohm resistor directly to the output of the modulator.
Working on the assumption that the emitter is on the left and subtly marked E it goes to the pad shown:
Which makes sense as the input to R134 now comes from the 12V carrying cap and goes down to blanking voltage level via the new R134, the other side of which goes directly into pin 1.
So from here on in I am just basically connecting the emitter output via a 75ohm resistor directly to the output of the modulator.
ZX80
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
- 1024MAK
- Posts: 5165
- Joined: Mon Sep 26, 2011 10:56 am
- Location: Looking forward to summer in Somerset, UK...
Re: Spectrum+ 128K Toastrack composite out
Yeah
Mark
Mark
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer being good this year.
ZX81 Chip Pin-outs
ZX81 Video Transistor Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer being good this year.